If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Needed: Download site for Wurlitzer 3500 Zodiac SCHEMATIC
I know it takes many pages to tape together but I've done that before. I
have a manual just ordered from Jeff Wager but client pressure to repair it for the weekend if possible. Thanks, Al Last contact me at Remove the (dot) and replace with .. |
Ads |
#2
|
|||
|
|||
Needed: Download site for Wurlitzer 3500 Zodiac SCHEMATIC
On 2006-06-07 21:06:28 -0700, "Al Last" said:
I know it takes many pages to tape together but I've done that before. I have a manual just ordered from Jeff Wager but client pressure to repair it for the weekend if possible. Thanks, Al Last contact me at Remove the (dot) and replace with . Most problems with Wurlitzers are bad or noisy microswitches. I recommend that you test ECRY microswitch with an ohm-meter before moving on to other potential issues. The other area to check are the latch switches on the keyboard, clean them with a points file and adjust to the manual. Go to http://www.flippers.com/juke-tip.html and read that page... John :-#)# -- (Please post followups or tech enquires to the newsgroup) John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, Video Games) www.flippers.com "Old pinballers never die, they just flip out." |
#3
|
|||
|
|||
Needed: Download site for Wurlitzer 3500 Zodiac SCHEMATIC
On 2006-06-08 22:13:00 -0700, John Robertson said:
On 2006-06-07 21:06:28 -0700, "Al Last" said: I know it takes many pages to tape together but I've done that before. I have a manual just ordered from Jeff Wager but client pressure to repair it for the weekend if possible. Thanks, Al Last contact me at Remove the (dot) and replace with . Most problems with Wurlitzers are bad or noisy microswitches. I recommend that you test ECRY microswitch with an ohm-meter before moving on to other potential issues. The other area to check are the latch switches on the keyboard, clean them with a points file and adjust to the manual. Go to http://www.flippers.com/juke-tip.html and read that page... John :-#)# Typo...sigh... meant "test EVERY microswitch" John :-#)# -- (Please post followups or tech enquires to the newsgroup) John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, Video Games) www.flippers.com "Old pinballers never die, they just flip out." |
#4
|
|||
|
|||
Needed: Download site for Wurlitzer 3500 Zodiac SCHEMATIC
Thanks John for the advise. Yes I agree with you on the microsw problems. I
too have repaired many of the 3000 and american series. More than I really want to admit to. I promised the wife I'd NEVER bring another of that series in our garage again. Oh well, the things ya do for a buck. I have most of the 1800-3700 manuals except the diac 3500. It is slightly different credit accumulator. I already checked and replace about 4 micros last week. I've adjusted and cleaned the selection panel and relay contacts etc. I need to check the timing of the sw closures under the keyboard as I think RY2 START relay isn't getting a chance to lock in fast enough to allow the stepper to register the XY selection, rotate to it's location, and punch in the pin. I'm working on it as I write this email so probably have it repaired before manual arrives from Jeff Wager monday. Thanks again, Al Last pins4us "John Robertson" wrote in message news:2006060912252811272-spam@flipperscom... On 2006-06-08 22:13:00 -0700, John Robertson said: On 2006-06-07 21:06:28 -0700, "Al Last" said: I know it takes many pages to tape together but I've done that before. I have a manual just ordered from Jeff Wager but client pressure to repair it for the weekend if possible. Thanks, Al Last contact me at Remove the (dot) and replace with . Most problems with Wurlitzers are bad or noisy microswitches. I recommend that you test ECRY microswitch with an ohm-meter before moving on to other potential issues. The other area to check are the latch switches on the keyboard, clean them with a points file and adjust to the manual. Go to http://www.flippers.com/juke-tip.html and read that page... John :-#)# Typo...sigh... meant "test EVERY microswitch" John :-#)# -- (Please post followups or tech enquires to the newsgroup) John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, Video Games) www.flippers.com "Old pinballers never die, they just flip out." |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Here ya go; proof of that site | Sue H | Autographs | 0 | March 17th 06 10:42 PM |
How to install arm on Wurlitzer 3500 Zodiac | Kevin Rhinehart | Juke Boxes | 1 | October 29th 05 09:47 AM |
Antiquarian Bookman auction site: Beta Test Start July 6 | Jonathan Grobe | Books | 12 | July 8th 04 08:03 PM |
web site hints needed | Massimo at HOME | Coins | 1 | January 27th 04 11:32 AM |
8x10 Photo Site Abuse | dahoov2 | Autographs | 5 | October 4th 03 06:31 AM |