Hi, I'm finally getting around to a 716 I've had for many years. If anyone has an original to compare my questions to, hear they a 1) Lamp sockets in front ceiling of mechanism door- There is one white porcelain lamp fixture screwed into the ceiling of the box on either side. Wiring runs between...

To anyone concerned (or bidding): This ebay auction is using pictures and text from my original auction from 2006 without my concent. This is most likely a fake auction poised to steal money from whoever wins. I've alerted ebay about this matter but I though I would give the jukebox community an...

Does anyone know how the turntable shaft/clutch assembly is supposed to work on a '37 Wurlitzer 616? My son and I are working on restoring a badly forgotten Wurlitzer 616. We've done pretty well cleaning it up an recon so far, but we've run into an issue we can't figure out. The cam tries to...

Hi everyone. Just acquired a very nice Wurlitzer 61. She needs a few bits. Can anyone hook me up with the following? 30487- name plate escutcheon 30488 - name plate croglass 31703 - Selector front plate Many thanks. George in jersey

Hello All. I have just won an auction for a Wurlitzer 61 Countertop Jukebox. The Seller has told me it needs a new needle and several tubes. It is also missing the post on the top of the jukebox. Please tell me the best needle to use to produce the best sound from this jukebox and what tubes I...

If you have these parts please contact me at www.antiquecoinops.com Visit my Coin Operated Machine Website. http://antiquecoinops.com

I heard there is a place in Wisconsin that rebuilds jukebox amps for around 125-150. I have a amp out of a Wurlitzer 600 that needs it. Anyone know of this place? Thanks.

Hi everyone, this mech is making the wrong selectionif you let it free wheel, (don't select anything), it will count every other selection, from 2 to 12, then, it will go to 13, 14, 15, and get every selection consecutively to 24, then it misses #1, and goes to 2, 4, 6 etc, to 12 ( every other...

Does anyone have a source for the wire wound resistor on these amps? The dual resistances are 1450 and 9000 ohms?

Hello I'm looking for an original Wurlitzer 510 amplifier for my 1250 jukebox. The one I have has been radically modified and is missing parts. An unrestored or rebuilt amp in original configuration is what I'm looking for. I enjoy the discourse and have picked up quite a few tips over the...

Can someone PLEASE tell me what to check when my Wurlitzer 45 rpm OMT jukebox will rotate the mech but won't actually grab a record & play it?? THANKS in advance!

Working on a OMT Selection credit computer the Mbox 5.0 software is corrupt. does anyone know where I can download the software? Thanks in advance!

I know i can only get so much from a 78 player but ... Is there any known upgrades to this amp for more bass . Its all high pitch shrill treble . There is bass but the treble overpowers it . Amp and cartridge have been rebuilt and it plays loud & clear .. to clear :-)

Hi Guys. I am abou to begin work on a pair of Wurlitzer 412s and need a couple of questions answered. Neither machine had a volume control, one had an amp but no model number on it and finally one had, what appears to be a 12 inch 600 ohm speaker in it. My questions are : what is the proper volume...

Does anyone know if the cabinet front metal parts have been reproduced ? I need the two decorative pieces - the round piece that covers the selection buttons, and the coin slide entry cover. If these have not been reproduced, and anyone has either or both available, please contact me. Thanks Joe

I am trying to restore an original Wurlitzer 4008 speaker for a customer. I've never even seen one before until now. His is missing the center hub. I know that Victory Glass has complete hub replacements, but even they admit they are for a Rock-ola (?) reproduction, and are not completely sure if...

I recently finished a restoration on a 4008 speaker. It's very heavy, and I'm not sure how to properly hang it. I know there are two "eyehooks" that came with the speaker (from auction). These bolts are threaded at the straight end, and curve like the letter J at the other end. I figure the speaker...

Hi, What are the best sources for turntable drive belts for Wurlitzer 3600 & 3800 machines?

I have a working 1050 in the house. The tone-arm on this one has threaded adjustable weights attached in the rear, easily adjustable. The manual calls for what sounds like some expensive instrument dedicated to measuring the proper performance tone-arm pressure on the records, Needless to say, I...

Working on a machine that has been butchered and need a few odd parts. If you have a parts mech these parts are not normally worn or broken. 3700 mech model 1050. Manual info: Page 36C Item 13 part # 137911 spring, Clamp lever Page 38C Item 13 part # 137977 lever and clamp assembly Page 38C Item...